traceroute我们可以知道信息从你的计算机到互联网另一端的主机是走的什么路径。当然每次数据包由某一同样的出发点（source）到达某一同样的目的地(destination)走的路径可能会不一样，但基本上来说大部分时候所走的路由是相同的。 常见命令参数
Options:
-4 Use IPv4
-6 Use IPv6
-d –debugERP系统，进销存系统，货代系统，日用品ERP系统 Enable socket level debugging
-F –dont-fragment Do not fragment packets
-f first_ttl –first=first_ttl
Start from the first_ttl hop (instead from 1)
-g gate,… –gateway=gate,…
Route packets through the specified gateway
(maximum 8 for IPv4 and 127 for IPv6)
-I –icmp Use ICMP ECHO for tracerouting
-T –tcp Use TCP SYN for tracerouting
-i device –interface=device
Specify a network interface to operate with
-m max_ttl –max-hops=max_ttl
Set the max number of hops (max TTL to be
reached). Default is 30
-N squeries –sim-queries=squeries
Set the number of probes to be tried
simultaneously (default is 16)
-n Do not resolve IP addresses to their domain names
-p port –port=port Set the destination port to use. It is either
initial udp port value for “default” method
(incremented by each probe, default is 33434), or
initial seq for “icmp” (incremented as well,
default from 1), or some constant destination
port for other methods (with default of 80 for
“tcp”, 53 for “udp”, etc.)
-t tos –tos=tos Set the TOS (IPv4 type of service) or TC (IPv6
traffic class) value for outgoing packets
-l flow_label –flowlabel=flow_label
Use specified flow_label for IPv6 packets
-w waittime –wait=waittime
Set the number of seconds to wait for response to
a probe (default is 5.0). Non-integer (float
point) values allowed too
-q nqueries –queries=nqueries
Set the number of probes per each hop. Default is
3
-r Bypass the normal routing and send directly to a
host on an attached network
-s src_addr –source=src_addr
Use source src_addr for outgoing packets
-z sendwait –sendwait=sendwait
Minimal time interval between probes (default 0).
If the value is more than 10, then it specifies a
number in milliseconds, else it is a number of
seconds (float point values allowed too)
-e –extensions Show ICMP extensions (if present), including MPLS
-A –as-path-lookups Perform AS path lookups in routing registries and
print results directly after the corresponding
addresses
-M name –module=name Use specified module (either builtin or external)
for traceroute operations. Most methods have
their shortcuts (`-I’ means `-M icmp’ etc.)
-O OPTS,… –options=OPTS,…
Use module-specific option OPTS for the
traceroute module. Several OPTS allowed,
separated by comma. If OPTS is “help”, print info
about available options
–sport=num Use source port num for outgoing packets. Implies
`-N 1′
-U –udp Use UDP to particular port for tracerouting
(instead of increasing the port per each probe),
default port is 53
-UL Use UDPLITE for tracerouting (default dest port
is 53)
-P prot –protocol=prot Use raw packet of protocol prot for tracerouting
–mtu Discover MTU along the path being traced. Implies
`-F -N 1′
–back Guess the number of hops in the backward path and
print if it differs
-V –version Print version info and exit
–help Read this help and exit 常见命令展示 多命令使用
traceroute -n -m 5 -q 4 -w 3 www.bway.cn 说明： -n 显示IP地址，不查主机名， -m 设置跳数 -q 4每个网关发送4个数据包 -w 把对外发探测包的等待响应时间设置为3秒 探测包使用的基本UDP端口设置6888
traceroute -p 6888 www.bway.cn 绕过正常的路由表，直接发送到网络相连的主机
traceroute -r www.bway.cn 本篇文章到此结束，如果您有相关技术方面疑问可以联系我们技术人员远程解决，感谢大家支持本站！
文章来源于网络，如有侵权，请联系删除。
我司专注于ERP软件开发，ERP生产管理软件，客户管理软件开发，进销存软件，
企业微信ERP生产管理软件，销售管理，生产管理，采购管理，客户管理，BOM物料管理，财务管理，统计分析于一体ERP管理软件，分手机APP ERP管理软件，企业微信ERP软件。多年来一直专于研发，销信于一体软件公司。